ASTM E466 PDF

Download scientific diagram | Typical sample for fatigue test according to ASTM E Standard. from publication: Effect of Hot Isostatic Pressure treatment on. ASTM E , Standard practice for conducting force controlled ASTM E , Standard terminology relating to fatigue and fracture testing 1). ASTM E covers axial force controlled fatigue tests of metallic materials in the fatigue regime where strains are predominately elastic, both at initial loading.

Author: Fegul Mezilrajas
Country: Guinea
Language: English (Spanish)
Genre: Marketing
Published (Last): 4 April 2013
Pages: 453
PDF File Size: 16.39 Mb
ePub File Size: 20.58 Mb
ISBN: 935-5-61799-441-8
Downloads: 97657
Price: Free* [*Free Regsitration Required]
Uploader: Mosida

The acceptable ratio of the areas test section to grip section to ensure a test section failure is dependent on the specimen gripping method. The ASTM E axial load fatigue test is used to determine the effect of variations in material, geometry, surface condition, stress, etc. Readers are referred to Ref 1 should this occur. This practice is not intended for application in axial fatigue tests of components or parts. In view of this fact, the method of preparation should be agreed upon prior to the beginning of the test program by both the originator and the user of the fatigue data to be generated.

Specimens can be round or flat. NOTE 2—Measurements of dimensions presume smooth surface?

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. ASTM E covers axial force controlled fatigue tests of metallic materials in the fatigue regime where strains are predominately elastic, both at initial loading and throughout the test. Continue sinusoidal cycles to failure.

To ensure test section failure, the grip cross-sectional area should be at least 1.

Also, Refsalthough they pertain to straincontrolled testing, may prove of interest since they deal with sheet specimens approximately 0. As a conservative general measure, this procedure is recommended unless: It is important that the accuracy of alignment be kept consistent from specimen to specimen.

Fillet undercutting can be readily determined by inspection. For tests run in compression, the length of the test section should be approximately two times the test section diameter to minimize buckling. Touchstone is experienced in the performance of fatigue testing in almost every material system and at a wide variety of temperatures from cryogenic to over ?

  ABHIJIT GUHA QUANTITATIVE APTITUDE PDF

This practice is not intended for application in axial fatigue tests of components or parts. All material variables, testing information, and procedures used should be reported so that correlation and reproducibility of results may be attempted in a fashion that is considered reasonably good current test practice.

Static and fatigue forces up to 50 kN 11, lbf Frequency ratings up to 75 Hz Oil-free, all electric actuator for clean test conditions Lower purchase, operating, and mantenance costs than hydraulic equivalents.

ASTM International takes no position respecting the asm of any patent rights asserted awtm connection with any item mentioned in this standard. One set of strain gages should be placed at the center of the gage length to detect misalignment that causes relative rotation of the specimen ends about axes perpendicular to the specimen axis.

Give our test engineers a call today for help configuring the best test machine and accessories according to ASTM E This knowledge and care provides the most meaningful and best possible high cycle fatigue life results.

The test may also be used as a guide to the selection of astj materials for service under conditions of repeated direct stress. ASTM E is limited to the fatigue testing of axial unnotched and notched specimens subjected to a constant amplitude, periodic forcing function in air at room temperature. The reduced section length should be greater than three times the minimum test section diameter.

The trial specimen should be rotated about its longitudinal axis, installed and checked in both orientations within the? Wstm test forces should be monitored continuously in the early stage of the test and periodically, thereafter, to ensure that the desired force cycle is maintained.

ASTM E Load Controlled Constant Amplitude Fatigue Tests of Metals

Since specimen preparation can strongly in? Current edition approved Nov. Since however, the environment can greatly in? Obvious abnormalities, such as cracks, machining marks, gouges, undercuts, and so forth, are not acceptable. Historical Version s – view previous versions of standard.

  DREAM CARGOES JG BALLARD PDF

The test section length should be approximately two to three times the test section width of the specimen.

The ratio of specimen test section width to thickness should be between two and six, and the asmt area should preferably be between 0. We are confident that we have what you are looking for. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. One exception may be where these parameters are under study. The results may also be used as a guide for the selection of metallic materials for service under e66 of repeated direct stress.

The method is limited to the fatigue testing of axial unnotched and notched specimens subjected to constant amplitude, periodic forcing function in air at room temperature.

ASTM E466 – Force Controller Constant Amplitude Axial Fatigue Testing of Metallic Materials

The results may also be used as a guide for the selection of metallic materials for service under conditions of repeated direct stress. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Threaded end specimens may prove difficult to align and failure often initiates at these stress concentrations when testing in the life regime of interest in this practice.

For specimens that are less than 0. The storage medium should generally be removed before testing using appropriate solvents, if necessary, without adverse effects upon the life of the specimens.

Touchstone Research Laboratory, Ltd. The size of the gripped end relative to the gage section, and the blend radius from gage section into the grip section, may cause premature failure particularly if fretting occurs in the grip section or if the radius is too small.