For more details, refer Procedure 6, Test Condition K, Page no of Defence. Standard JSS Rev Low Temperature Test. 3 days ago , Document No. Nomenclature, Standardisation Sub-Committee. , (Third Revision), COMPOSITION FLARES, BEACON. recommended as per JSS, Military standard, Class L2H category, and functional specifications and no damages should be seen as an outcome of.

Author: Shakagore Misida
Country: Swaziland
Language: English (Spanish)
Genre: Environment
Published (Last): 18 December 2017
Pages: 26
PDF File Size: 12.84 Mb
ePub File Size: 1.24 Mb
ISBN: 993-4-92245-137-9
Downloads: 71316
Price: Free* [*Free Regsitration Required]
Uploader: Kajigami

While doing so, attention should be paid to the thermal geometry considerations of the equipment, if any, and if so specified in the relevant equipment specification. To be used in position shielded from the weather ashore and afloat. Controlling the dew point at 5 degrees F below the surface. Read this operation manual. After that caps are applied to the rods and tinned electrolytic copper wires are welded to these end caps.

Part 1 Wire cloth test sieves third revision Reaffirmed BS Land Services a L1: Metal glaze A metal glazed film is deposited on a high grade ceramic body. Liquid-in-glass thermometers selection, use and calibration Technical Note 19 March Issued: During the visual examination of the equipment, defects in construction, the presence of foreign bodies, moisture, dust, etc. Fleet air arm workshop and hanger test equipment unpacked To be used in exposed positions ashore and specificattions, but normally stowed in a protected sjs.


Corrosion acid see Note 1, 2 and 3 Corrosion alkaline see Note 1,2 and 8 3 Ultra-miniature size for PS pressure sensor.

Vibration Refer Table Sl. Shipborne equipment submersible unpacked: Start display at page:. These sensors shall be centrally located within the test chamber, where possible, or in the return air-stream and shall be baffled or otherwise protected against direct impingement of supply air and against radiation effects.

Ground equipment partially protected e L2D: Specifucations temperature Altitude Procedure 1 and 2 3 5.

This site is temporarily unavailable

II, 3 shocks per face 24 Note: June 11 th, Report Prepared By: To be used in positions completely exposed to the weather. In some of the tests, the test conditions are varied in order to enable the designers to select the conditions which will be adequate to meet the users qualitative requirements, commensurate with the design efforts. The following members have been associated in approving the draft.

Ground equipment ill d This specifications covers design, manufacture, testing at works and supply of composite type L. Keeping in view the stringent quality and operational requirements of the users, the Joint Services Specification No on Environmental Test Methods for Electronic and Electrical Equipment JSS was prepared in which was later revised in Considerable experience has been gained over the years since and this has necessitated revision of the existing JSS This document JSS on Environmental Test Methods for Electronic and Electrical Equipment has been reprinted with the various amendments incorporated.


Most of the Equipment have a restricted sphere of use which, by limiting the severity of conditions of use, may allow simplification of the design, with resultant reduction in cost.

August Amended and reissued: SI units and recommendations for the use of their multiples and of certain other units. Espotel Test Laboratory Services.

Read this operation manual and understand the description. DecemberJuneDecemberMarch Liquid-in-glass thermometers selection, use and calibration Copyright National.

JSS – Antifungal Test – Electronics | Situ Biosciences LLC

Vibration Refer Table and Sl see Note 28 8 2. To be used in the field or in a vehicle where it is fully exposed to the weather during storage and use and liable to immersion in water. Instruction Manual Instruction Manual Option Card for Frequency Divider Deliver this instruction manual without fail to those who actually operate the equipment.

Content This specificatkons covers performance, tests and quality requirements for the More information. After a helical groove has been specificatiions in the resistive More information. Where called for, it is the first process in the test procedure.